Starch/carbon nanofibers bionanocomposites via melt mixing: Effect of dispersion and compatibility on conductivity and mechanical properties.

Biodegradable polymers with conductivity and mechanical properties are required in several applications where it is necessary to substitute conductive synthetic plastics due to the high waste produced. In this study, bionanocomposites (BNCs) have been compounded by thermoplastification of rice starch via melt mixing with carbon nanofibers (NPs) and modified NPs (NPs [M]) using plasma of acrylic acid. Spectroscopy analysis, X-ray diffraction, and morphology were studied to elucidate the effect of dispersion and compatibility on the conductivity and mechanical properties. The incorporation of NPs promoted esterification reactions with starch during the melt mixing process, giving rise to changes in its crystal structure. NPs [M] showed better dispersion and compatibility because the plasma prevents reagglomeration and generates a stronger affinity. BNCs showed significative flexibility with remarked % elongation at break from 5.64 % to 248.60 %, and thermal conductivity increased from 0.10 to 0.58 W/m K, with NPs [M] at 5 %. In contrast, the electrical conductivity remained in the same magnitude order (10-4 S/cm). The better compatibility between starch-NPs [M] hinders electronic transport but increases the propagation of phonons to promote thermal conductivity. BNCs fabricated in this study by a dry and scalable process could be of interest in some application areas (intelligent food packing, electronics, textiles, etc.).

Fabrication of Woven Jute Fiber Epoxy Bio-Composites through the Epoxy/Thiol-Ene Photopolymerization Technique.

An eco-friendly epoxy/thiol-ene photopolymerization (ETEP) process was employed to prepare epoxy bio-composites using a commercial biobased epoxy resin and a woven jute fabric as reinforcement. In this process the components of the thiol-ene system, an allyl-functionalized ditertiary amine curing agent, a multifunctional thiol and a radical photoinitiator, were added to the epoxy resin to produce a polyether-polythioether crosslinked co-network. Moreover, the jute fibers were functionalized with thiol groups using the 3-mercaptopropyl (trimethoxysilane) with the purpose of creating a chemically bonded polymeric matrix/fiber system. The obtained bio-composites prepared with the thiol-functionalized cellulose fibers exhibited an increase up to 52% and 40% in flexural modulus and strength with respect to the non-functionalized counterparts. Under the three-point bending loadings, the composites displayed higher deformation at break and toughness due to the presence of polythioethers in the co-network. The prepared bio-composites developed in this work are excellent candidates to extend the use of cellulose fibers for structural applications.

Biobased sustainable materials made from starch and plasma/ultrasound modified Agave fibers: Structural and water barrier performance.

This study aims to investigate the effect of green modification methods (ultrasound and plasma treatment) on a by-product of the tequila industry (Agave fibers), which can be useful as raw material to elaborate biodegradable and hydrophobic starch films. FTIR analysis indicated a decrease of hydrophilic lignocellulosic components, since the cavitation and etching effect of ultrasound/plasma treatment reduced the large number of hydroxyl groups of the fibers. The inclusion of ultrasound/plasma modified fibers in the starch matrix limited the starch-glycerol interactions, reducing the free volume of the starch and the binding sites for water. Therefore, the solubility (%S), swelling (%W) and water vapor permeance (WVPe) of the films decreased from 27 to 16%, 57 to 50% and 0.37 to 0.21 g/day m2Pa, respectively. Furthermore, the water contact angle (WCA) and relative crystallinity values increased. The results indicated that the treatments are suitable green technologies to obtain hydrophobic fillers useful to develop sustainable materials.

Exogenous Application of Polycationic Nanobactericide on Tomato Plants Reduces the Candidatus Liberibacter Solanacearum Infection.

Candidatus Liberibacter solanacearum (CaLso) is associated with diseases in tomato crops and transmitted by the tomato psyllid Bactericera cockerelli. A polymeric water-dispersible nanobactericide (PNB) was evaluated against CaLso as a different alternative. PNB is a well-defined polycationic diblock copolymer designed to permeate into the vascular system of plants. Its assessment under greenhouse conditions was carried out with tomato plants previously infected with CaLso. Using a concentration as low as 1.0 mg L-1, a small but significant reduction in the bacterial load was observed by real-time qPCR. Thus, to achieve an ecologically friendly dosage and set an optimum treatment protocol, we performed experiments to determine the effective concentration of PNB to reduce ~65% of the initial bacterial load. In a first bioassay, a 40- or 70-fold increase was used to reach that objective. At this concentration level, other bioassays were explored to determine the effect as a function of time. Surprisingly, a real reduction in the symptoms was observed after three weeks, and there was a significant decrease in the bacterial load level (~98%) compared to the untreated control plants. During this period, flowering and formation of tomato fruits were observed in plants treated with PNB.

Combinations of Antimicrobial Polymers with Nanomaterials and Bioactives to Improve Biocidal Therapies.

The rise of antibiotic-resistant microorganisms has become a critical issue in recent years and has promoted substantial research efforts directed to the development of more effective antimicrobial therapies utilizing different bactericidal mechanisms to neutralize infectious diseases. Modern approaches employ at least two mixed bioactive agents to enhance bactericidal effects. However, the combinations of drugs may not always show a synergistic effect, and further, could also produce adverse effects or stimulate negative outcomes. Therefore, investigations providing insights into the effective utilization of combinations of biocidal agents are of great interest. Sometimes, combination therapy is needed to avoid resistance development in difficult-to-treat infections or biofilm-associated infections treated with common biocides. Thus, this contribution reviews the literature reports discussing the usage of antimicrobial polymers along with nanomaterials or other inhibitors for the development of more potent biocidal therapies.